We are an independent Nairobi repair company — not affiliated with Bosch Kenya. We repair out-of-warranty Bosch ovens, cookers and hobs at your home across all Nairobi areas. The Bosch E-NR is essential for oven repairs — Bosch produces many oven series with different heating elements, thermostats and control boards that are not interchangeable.
Bosch Oven Faults — All Types
| Fault | Likely Cause |
|---|---|
| Oven not heating at all | Failed bottom heating element (most common), failed thermostat, selector switch fault, control board KES 4,000–10,000 |
| Oven not reaching set temperature | Failed main element, thermostat calibration drift — test with oven thermometer before replacing KES 3,500–8,000 |
| Oven overheating and burning food | Failed thermostat or NTC sensor causing temperature runaway — stop using immediately KES 3,500–7,500 |
| Grill not working | Failed grill element — most common single Bosch oven repair in Nairobi KES 4,000–8,000 |
| Fan oven uneven results | Failed fan oven circular element or convection fan motor KES 4,000–9,000 |
| Touch controls not responding | Control board, moisture ingress, burnt ribbon cable KES 4,000–11,000 |
| Door not closing properly | Failed Bosch door hinge — a known wear item on Bosch built-in ovens KES 3,500–8,000 |
| Oven light not working | Bulb (Bosch uses specialist high-temp bulbs), holder, wiring KES 1,000–2,500 |
| Bosch oven error code displayed | E101/F101 temperature sensor, E105 cooling fan, E121 element fault, E301 control board KES 3,000–11,000 |
| Circuit breaker tripping | Element short circuit, wiring fault — requires safe electrical testing KES 3,500–8,000 |
Bosch Gas Hob Faults
- Burner not igniting — dirty blocked burner ports (most common), failed spark electrode, microswitch or ignition module
- Flame dies when knob released — thermocouple (FFD flame sensor) not heating fast enough; hold knob 10 seconds; if still failing, thermocouple needs replacement
- Weak or uneven flame — blocked burner ports from cooking spillage
Bosch Induction and Ceramic Hob Faults
- Zone not heating — failed IGBT power transistor (induction), failed element (ceramic), control board fault
- Touch controls not responding — moisture ingress, failed touch interface board, burnt ribbon cable
- Induction not detecting cookware — NTC sensor, control board, or non-induction cookware being used
- Error code displayed — various codes by model; E-NR required for accurate diagnosis
- Hob switching off unexpectedly — overtemperature protection triggered by blocked ventilation or fan failure
- Cracked glass — E-NR required for the correct model-matched glass panel
Bosch Oven Series We Service
Important: Bosch Oven Timer and Operation
Some Bosch oven models (particularly Series 4 and above) require the electronic timer/clock to be set correctly before the oven will operate. If the clock is flashing or in a timed mode, the oven will not heat even if all components are functional. Check the clock and manual end-time settings before concluding the oven has a fault. If the oven still does not heat after checking the timer, call 0742 245720 for diagnosis.
Pricing Guide — Nairobi 2026
Indicative prices only. We always diagnose first and provide a clear quote before starting any repair. Bosch E-NR required for accurate parts sourcing.
| Service | Estimated Cost KES | Notes |
|---|---|---|
| Oven bottom heating element | 4,000–8,000 | E-NR required for correct element |
| Fan oven circular element | 4,000–9,000 | E-NR required |
| Grill element | 4,000–8,000 | Most common single oven repair |
| Oven thermostat / NTC sensor | 3,500–7,500 | Parts + labour |
| Oven door hinge replacement | 3,500–8,000 | Known Bosch wear item |
| Oven door seal | 3,000–6,000 | E-NR required for correct seal |
| Control board (oven) | 4,000–11,000 | E-NR required |
| Gas thermocouple (hob) | 3,000–5,500 | Fixes flame-dies-on-release |
| Spark electrode (hob) | 2,000–4,500 | For no-ignition fault |
| Induction zone repair | 4,500–12,000 | IGBT or control board; E-NR required |
Nairobi Service Areas
Frequently Asked Questions
Check that the oven timer is in manual (not timed) mode — some Bosch ovens will not heat if the clock is in an automatic timer setting. If the timer is set correctly and the oven still does not heat, the most likely cause is a failed bottom heating element or oven thermostat. Call 0742 245720.
The thermocouple is not heating fast enough to hold the FFD safety valve open. Hold the knob for a full 10 seconds after ignition. If still failing, the thermocouple needs replacement at KES 3,000–5,500. Call 0742 245720.
First check the pan is induction-compatible (a magnet should stick to the base). If the pan is correct, the NTC sensor or control board may have failed. Bosch induction hob repairs require the E-NR as components vary significantly between models. Call 0742 245720.
Yes. We repair Bosch Pyrolytic ovens including the HBG Serie 6 and Serie 8 models. Pyrolytic ovens use higher temperatures and have additional door safety locking mechanisms. The E-NR is essential for sourcing the correct door hinge, seal and control board parts. Call 0742 245720.